Process of pasta products forming in matrix wells with pre-compaction, plasticization and heating of dough

The existing designs of domestic and foreign matrices lack pre-compaction, plasticization and heating of dough, which leads to significant hydraulic resistance in the area where dough flow enters the forming holes of the dies and increases energy consumption, while in typical matrices the cross section of deep and empty wells is much larger than the total area of forming holes. The dough flow almost becomes uncontrollable, and this leads to water hammer effect and destruction of dies. This problem can be solved by installing special inserts in in the matrix wells (depth of wells is 50-120 mm). The paper shows a new direction in design of matrices for production of pasta, in particular, it is proposed to install spiral inserts in the wells of matrix, manufactured in the form of Venturi tubes. Rheological basis of dough flow in the cylindrical channels of the insert are considered, mathematical models for determination of the dough volume flow rate and dough flow rate are constructed. It is theoretically established that the volume flow rate of the dough Q₀ and its flow rate depend on the length of the cylindrical channel and the viscosity of dough. The results of experimental researches are presented. It is empirically established that the inserts located in the wells of the matrix pre-compact dough, plasticize and heat it, the productivity of the press machine MIT-2 due to increasing the speed of extrusion is increased averagely by 25-26 % with significant improvement in quality of the formed semi-finished products and reduction of energy consumption.

1. Medvedev G. M. Technology of pasta production. Moscow, Kolos Publ., 1998. 271 p. (in Russian).

2. Sokolov A. Ya. Basis for calculating and design of machines and apparatus for food production. Moscow, Pishchepromizdat Publ., 1960. 742 p. (in Russian).

3. Gus’kov K. P., Azarov B. M. Perforated plates in pasta production. Moscow, 1965. 48 p. (in Russian).

4. Shcheglov N. G., Martirosyan V. V., Maklichenko O. A., Zhirkova E. V. The effect of pasta pressing parameters on press power. Upravlenie reologicheskimi svoistvami pishchevykh produktov: sbornik materialov pervoi nauchno-prakticheskoi konferentsii i vystavki s mezhdunarodnym uchastiem, 25-26 sentyabrya 2008 g. = The Management of rheological properties of food products: a collection of papers of the 1st scientific and practical conference and international exhibition, 25-26 September 2008]. Moscow, 2008, pp. 199-203 (in Russian).

5. Novikova G. V., Ivanov B. C. Pasta press. Mekhanizatsiya i elektrifikatsiya sel’skogo khozyaistva [Mechanization and Electrification of Agriculture], 2011, no. 12, pp. 26-27 (in Russian).

6. Chernykh V. Ya., Mitin V. Yu., Sarbashev K. A. Formation of requirements for modern laboratory pasta unit. Khlebopechenie Rossii = Baking in Russia, 2015, no. 5, pp. 26-28 (in Russian).

7. El’mesov R.R., Didanov A.M., Tlishev A.B., Didanov M.Ts. Development and research press small-sized for pasta. Sovremennye problemy nauki i obrazovaniya = Modern Problems of Science and Education, 2015, no. 2, pt. 1. Available at: http://www.science-education.ru/ru/article/view?id=20358 (accessed: ) (in Russian).

8. Romanchikov S. A. Pasta pressing device with ultrasonic capillary effect. Nauchnaya zhizn’ = Scientific Life, 2019, vol. 14, no. 4 (92), pp. 463-471 (in Russian). https://doi.org/10.26088/INOB.2019.92.30192

9. Nazarov N. I. Technology of pasta. 2nd ed. Moscow, Pishchevaya promyshlennost’ Publ., 1978. 287 p. (in Russian).

10. Kishtykov Kh. B., Ul’basheva M. I. The influence of the temperature of the matrix to the parameters of pressing and quality pasta. Alleya nauki [Alley Science], 2017, vol. 1, no. 9, pp. 720-728 (in Russian).

11. Gnatuv E., Chernov M. The influence of wear of forming holes of pasta matrix on product quality indicators. Khleboprodukty, 2009, no. 10, pp. 48-49 (in Russian).

12. Grigolyuk E. I., Fil’shtinskii L. A. Perforated plates and shells and related problems: a review of the results. Uprugost’ i plastichnost’, 1965 [Elasticity and Plasticity, 1965]. Moscow, 1967, pp. 7-163 (in Russian).

13. Smolentsev Yu. A. Experimental determination of the attenuation coefficient of stretched perforated plates. Khimicheskoe i neftyanoe mashinostroenie [Chemical and Petroleum Engineering], 1966, no. 6, pp. 12-13 (in Russian).

14. Mel’nikov N. P. Constructive forms and methods for calculating nuclear reactors. Moscow, Gosatomizdat Publ., 1963. 519 p. (in Russian).

15. Gogolev A. Ya. Experimental determination of the attenuation coefficient of tube plates. Energomashinostroenie [Power Plant Engineering], 1962, no. 10, pp. 38-39 (in Russian).

16. Ponomarev S. D. (ed.). Strength calculations in mechanical engineering. Vol. 1. Theoretical foundations and experimental methods. Calculations of bar structural elements under static load. Moscow, Mashgiz Publ., 1956. 884 p. (in Russian).

17. Skatetskii V. G. Mathematical modeling of physical and chemical processes. Minsk, Vysheishaya shkola Publ., 1981. 144 p. (in Russian).

18. Torgan A. B. Analysis of rheological aspects of pasta flow in step-variable cross-section channels with the use of nonlinear Herschel-Bulkley model. Pishchevaya promyshlennost’: nauka i tekhnologii = Food Industry: Science and Technology, 2015, no. 3 (29), pp. 64-71 (in Russian).

19. Grudanov V. Ya., Pozdnyakov V. M., Brench A. A., Torgan A. B. Mathematical modelling of a pasta moulding process in a matrix with improved hydraulic and technological characteristics. Vestsi Natsyyanal’nai akademii navuk Belarusi. Seryya fizika-tekhnichnykh navuk = Proceedings of the National Academy of Sciences of Belarus. Physical-technical series, 2012, no. 3, pp. 57-65 (in Russian).

20. Torgan A. B. Method of assessing the contribution of plastic and viscous components in resistance to flow of pasta dough. Vesnіk Grodzenskaga dzyarzhaunaga unіversіteta іmya Yankі Kupaly. Seryya 6. Tekhnіka = Vesnik of Yanka Kupala State University of Grodno. Series 6. Engineering Science, 2015, no. 1 (198), pp. 90-98 (in Russian).

21. Grudanov V. Ya., Torgan A. B., Brench A. A., Poznyakov V. M. Research of the basic characteristics of a forming mechanism for pasta manufacturing. Vestsi Natsyyanal’nai akademii navuk Belarusi. Seryya agrarnykh navuk = Proceedings of the National Academy of Sciences of Belarus. Agrarian series, 2011, no. 2, pp. 103-110 (in Russian).